| 维修TDY型 油冷式电动滚筒 |
| 添加时间：2018/1/16 18:10:20 浏览次数： |
| 首先介绍一下电动滚筒的适用范围；油冷式电动滚筒是皮带传输机的驱动装置，具有以下优点： 结构简单紧凑，密封良好，占用空间面积小，可用于粉尘大，潮湿泥泞的场所； First, introduce the application scope of the electric roller. The oil cooled electric cylinder is the driving device of the belt conveyor. It has the following advantages: the structure is simple and compact, the seal is good, the space occupation is small, and it can be used in the big, wet and muddy place. 2电动滚筒全部零件放放滚筒空腔内，外观整齐， 2 the all parts of the electric roller are placed in the cavity of the drum, and the appearance is neat. 电滚筒内部结构 Internal structure of electric roller 1 滚筒边盖（左）2 内齿圈 3 齿轮 4 电机右端盖 5 右法兰轴 6 左法兰 7 电机转子轴齿 8 电机左端盖 9电机壳 （定子）10 滚筒端盖(右）11 滚筒出线头(接线盒）. 1 roller side cover (left) 2 inner gear ring 3 gear 4 motor right end cover 5 right flange shaft 6 left flange 7 motor rotor shaft 8 motor left side cover 9 motor shell (stator) 10 roller end cover (right) 11 roller outlet line (junction box). 一 维修故障原因..因接触器 .触点老化. 导致一项虚连 .电机缺项烧毁、、（因拆线时忙碌 无烧毁照片） The cause of the maintenance of the fault.. the contacts. Contact aging. Cause a virtual connection. The motor is missing. 二 .拆装时注意事项 Two. Precautions for disassembly and disassembly 1、拆滚筒时 划好筒体与端盖 螺丝眼距位置 两面滚筒端盖都划. （防止组装时对不上螺丝位置） 1. When the cylinder is dismantled, both the cylinder and the end cap are positioned on both sides of the cylinder. 2 、电机端盖处密封圈 要保证无脏 后安装 . 2, the seal ring at the end cover of the motor should ensure no dirty installation. 3 、 电机部分装好后 试转 （确认电机。相间电阻 对地电阻 正常。轴承无噪音 后继续安装 ）， 3, the motor part is installed after the test turn (confirm the motor. The resistance of the phase to the earth is normal. The bearing continues to be installed without noise. 4 、组装时螺丝不要有松动 忘紧、、（筒内螺丝掉落后果严重） 4, the screw should not be loosened and tightened when the assembly is assembled. 5、筒体与端盖之间旧垫 清理干净 不要有残留。做新垫时注意 尺寸 眼距 正好、做好后纸垫两面 打好密封胶 抹匀.。（不要过多抹胶、紧螺丝纸垫易挤裂） 5, the old pad between the barrel and the end cover is clean and clean. When doing the new mats, pay attention to the size of the eye distance, and make the sealant on both sides of the pad. (not too much glue, tight screwpaper pad is easy to crack) 6 、安装筒体时尽量将内部组好一部分竖起来装 （更方便 对 之前划过的记号 ，另观察纸垫是否完好 。） 6, when installing the cylinder, try to set up a good part of the internal group in a good way (more convenient to mark the past, and to see if the paper pad is intact.) 7 、 装好后刮去多余部分纸垫 、完成安装 7. After loading, scraping off the redundant paper pads and completing the installation 下面分享下 TDY型 油冷式电动滚筒 两个注意事项 及 采购参数 性能参数表 。 Below to share the TDY oil cooling type electric roller two points of attention and purchasing parameters performance parameters table. 1电动滚筒采用油冷或油浸式电动机，当环境温度不超过40℃时，能够安全运转。 1 electric roller is oil cooled or oil immersed motor, and it can operate safely when the environment temperature is not more than 40. 2电动滚筒不适用于高温物料输送机 2 electric roller is not suitable for high temperature material conveyor 采购参数： 1功率（P） 2胶带速度（V） 3胶带宽度（B） 4滚筒直径（D） Purchasing parameters: 1 power (P) 2 tape speed (V) 3 tape width (B) 4 drum diameter (D) 例：订购功率P=7.5千瓦 胶带速度V=1.25米/秒 胶带宽度B=500毫米 滚筒直径D=400毫米 则‘滚筒型号号为:YD-750·125·50·40 （型号直供参考 ） Example: order power P=7.5 kW tape speed V=1.25 M / sec tape width B=500 mm roller diameter D=400 mm, then drum number is: YD-750. 125. 50. 40. |
| 上一页 动力滚筒输送机的操作及维护 |
| 下一页 压滤机皮带传输机特点和性能优缺点分析 |
Copyright © 技术支持：遨游网络